PRODUCTS

PLATE HEAT EXCHANGER

Byone series of plate heat exchanger can be divided by different flow of conventional forms into four series: regular, shallow dense ripple, asymmetrical, and free flow. There are 18 models, which is from DN25 to DN500 interface diameter, plate thickness from 0.5 to 1.0mm. to match users different conditions of heat transfer and pressure drop performance.

Each model is subdivided into large-angle and small-angle chevron of corrugated plate (expect deep-wide flow channel plate). These plate covered shallow grooves, deep grooves and ultra-deep grooves deep trough three different specifications, after the assembling they were formed narrow channel and extra-wide channel plate heat exchanger.

features of plates:

• more efficient of heat transfer, for the same conditions, the Byone series of plate heat exchanger is more efficient, not only save investment, but also have higher partitioned velocity, which reduces the plate corrosion and scaling speed.
  
  
• All single design flow plate heat exchanger is the best form because unilateral takeover to the clients’ great convenience on installation and maintenance. Many large aspect ratio plates can cover the large number of transfer units of the operating conditions, avoid the multi-process design
  
  
• Design take over the entire single-receiver design is a bilateral receivership, is not a good design forms. Rich plate models including many corner hole plates (the largest is 500mm), the flow is up to 3,000 tons per hour. It can completely prevent the two-pipe design.
  
  
• Satisfies the special request to be easier to satisfy the user such as height or the length limit takes over control of the size request or the number limitation depending on the special request
  
  
• Higher Pressure. Plate’s unique high-rigid structure design, product design pressure can up to 2.5MPa;

Martial of Plates:

• All our plate heat exchangers are available in different materials
• Plate materials:
• SS304 (1.4301)
• SS316 (1.4401)
• SS317 (1.4439)
• SS904 (1.4539)
• Titanium Gr.1
• SMO 254
• Alloy C-276
• etc

Design of Plates:

• Uses the superfine network the value simulation technology union precise experiment measuring technique, designs flows with the heat-transfer property superior heat transfer slab
  
  
• Plates at low velocity can produce high turbulence and high heat transfer coefficient
  
  
• Compare with other manufacturers’ plates, under the same circumstances, the plate has the smaller friction coefficient under the certain heat transfer coefficient.
  
  
• Chevron corrugated plate in the plate between as many as several thousand points of contact. Suppress the plate with high precision, it makes plate contact point between the confined uniform, It will be able to bear as much as more than 2.5 MPa pressure.
  
  
• Plates of imports triage area in the design flow line guide groove, it has narrowed the different channel flow resistance different role makes fluid in plate heat exchanger regional distribution, so as to avoid the uneven flow distribution and flow of dead ends caused by heat transfer efficiency, pitting and scaling, and other ills.
  

Martial of Gaskets:

• NBR
• HNBR
• EPDM
• Viton E
• Viton G
• Viton GF
• etc

Gaskets

Gaskets are used internationally reputable manufacturers for the manufacture from raw materials, have a long service life. In between the hot and cold fluid sealing set up two middle leaking area. Whether cold or hot fluid seal damage occurred, the leakage of fluid will go outside by the district will be designed from the gaskets leaking hole, but not mutual mixing. Its unique design convex section of the whole plate clamping group in each other cab, to avoid dislocation, greatly enhancing the sealing performance. Its installation is divided into two methods: Stickiest (Glued) and the button (Clip on) or adhesive - free (Glue-less)

Component of Plate Heat Exchanger

By using four corner localizations technologies, it can guarantee the seal maintains the identical position, the plates won’t be broken even the high pressure or the big area application. It cannot be off because of the operating mode. That’s why it can guarantee safe, reliable and the long life.

The advanced frame design technology, guaranteed the plates won’t be broken in the operation. It’s easy to install, only needs one person to complete the disassembling and assembling.

Uses the combination of H and V plate design technology, enables the heat transfer to achieve the highest efficient, the heat exchanger can be more economically and reasonable.